VERBOSE logger.c: - (11 headers 0 lines). Remote-Party-ID: "sip251" privacy=off screen=no VERBOSE logger.c: set_destination: set destination to 192.168.1.151, port 5060 DEBUG chan_sip.c: Strict routing enforced for session 19 00:14:32] VERBOSE logger.c: set_destination: Parsing for address/port to send to VERBOSE logger.c: Non-codec capabilities (dtmf): us - 0x1 (telephone-event), peer - 0x1 (telephone-event), combined - 0x1 (telephone-event) VERBOSE logger.c: Capabilities: us - 0x4 (ulaw), peer - audio=0xc (ulaw|alaw)/video=0x0 (nothing), combined - 0x4 (ulaw) VERBOSE logger.c: Found audio description format telephone-event for ID 101 VERBOSE logger.c: Found audio description format PCMA for ID 8 VERBOSE logger.c: Found audio description format PCMU for ID 0 VERBOSE logger.c: Found RTP audio format 101 VERBOSE logger.c: Found RTP audio format 8 VERBOSE logger.c: Found RTP audio format 0 VERBOSE logger.c: - (13 headers 13 lines). X-Netborder-Detailed-CPD-Result-v2-0: Unknown My outside connection to my provider goes via the asterisk server via IAX2 but i made a internal SIP trunk connection via CPA with my asterisk server so i'm assuming that should work. This one connects from VICIDIALCPAASTERISK (IAX2) For the other carrier i see a message 'recovery on timer expire' and then it ends. When add the CPA proxy to the carrier configs and make a testcall it seems for one carrier to connect and then immediately disconnect. I have two different carriers in VICIdial which both work fine when i make a test call via a softphone manually. I changed the SIP port inside the CPA config files from 5062 to 5060 and restarted the services. Is that still the case? I noticed the guide was a bit out-of-date.Īnyway, i have succesfully installed and was enable to start both of the services.Īs far as i could tell i did not need to recompile asterisk because i'm running 1.4.21.2 which i've read is already patched. I read in the wiki guide here that it only works on Intel: After setting of the Zoiper softphone I try to get it to communicate with Asterisk, but I get a 408 request timeout.So to help analyzing my huge problems with disconnected numbers and the autodialing processes halting i have installed Sangoma Netborder CPA on a Windows 2008 AMD server for testing. I'm doing all of this without access to an internet connection so that's why I hardcode the IP address.ħ. In Zoiper I hardcode the Domain: :5080 and also enter the username and password.Ħ. I install and setup the Zoiper Softphone as indicated in the tutorial. I start asterisk with "asterisk" and "asterisk -rvvvvvv"Ĥ. I've modified sip.conf and nf to have entries that tie together phones 101 and 102ģ. I Integrate Kamailio and Asterisk based off of the asipto kb: 4.0.x-asterisk-11.3.0-astdb with both of them running on the same VM.ģ. I'm running Ubuntu 14.04 and Oracle Virtual BoxĢ. I have a virtual environment setup and am trying to get the integration of Kamailio and Asterisk to a least be able to make a phone call based off the Asterisk Hello World example. Subject: Asterisk Integration w Kamailio and Zoiper phone problems In Zoiper I hardcode the Domain: :5080 // make sure it is kamailio addrees, not asterisk address Previous message: Asterisk Integration w Kamailio and Zoiper phone problems.Asterisk Integration w Kamailio and Zoiper phone problems toasterisk at toasterisk at Asterisk Integration w Kamailio and Zoiper phone problems
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |